電工鋼硅鋼片絕緣涂層特性7.2.1 絕緣涂層狀態產品通常以兩面涂敷絕緣涂層狀態交貨，涂層種類見表 2。絕緣涂層應可耐受絕緣漆、江西景德鎮當?shù)刈儔浩饔?、江西景德?zhèn)附近機械油等介質的侵蝕。本文件規定的絕緣涂層與國內外相關技術規范規定絕緣涂層的近似對照可參見附錄 A(資料性附錄)，無取向電工鋼絕緣涂層的特性見附錄 B(資料性附錄)。絕緣涂層的厚度、江西景德鎮附近自粘接涂層的剝離強度等技術要求如有特殊要求應在訂貨時協商，并在合同中注明。7.2.2 絕緣涂層附著性根據附錄 C（無取向電工鋼絕緣涂層附著性檢測和評級方法），產品的絕緣涂層的附著性級別按照附著性由高至低分為 A、江西景德鎮附近B、江西景德鎮附近C、江西景德鎮附近D 四個級別。供貨時，產品涂層的附著性級別 應達到C 級。在剪切過程和供方規定的熱處理條件下進行熱處理時，涂層不得有大面積脫落，但是在剪切邊緣位置，涂層的輕微碎裂則允許存在。7.2.3 涂層絕緣電阻涂層絕緣電阻分為表面絕緣電阻和層間電阻，表面絕緣電阻單位為Ω·cm2/面，層間電阻單位為Ω·cm2/片，理論上，層間電阻是表面絕緣電阻的 2 倍。根據需方要求，經供需雙方協商，可進行涂層絕緣電阻的檢測，并在合同中注明涂層表面絕緣電阻或?qū)娱g電阻的小值

電工鋼硅鋼片Electrical steel, also known as silicon steel sheet, is an indispensable metal material in the power, electronics, and military industries, and is also the largest functional material in production. It is mainly used as the iron core for various motors, generators, and transformers. Since it is a functional material, its performance testing also revolves around "function". These indicators are often mentioned in trade and processing processes, and a brief understanding can help everyone better carry out their work. The performance testing of electrical steel mainly includes the following aspects: magnetic inspection, stacking coefficient inspection, coating adhesion inspection, repeated bending inspection, size and shape surface inspection, and conventional mechanical property inspection. In addition to the types of products listed above, there are also some special purpose electrical steel plates, such as 0.15 and 0.20mm thick 3％ Si cold-rolled non oriented silicon steel strips and 0.025, 0.05, and 0.1mm thick 3％ Si cold-rolled oriented silicon steel strips, which are used as intermediate and intermediate grade High frequency motors and transformers, as well as pulse transformers, etc； 0.7mm thick 3％ Si high-strength cold-rolled non oriented silicon steel plate for relays and power switches； High strength cold-rolled electrical steel plate for new high-speed motor rotors； Low carbon electrical steel hot-rolled thick and cold-rolled plates for magnetic shielding and high-energy accelerator electromagnets such as medical magnetic resonance tomography scanners； 4.5％ to 6.5％ Si high silicon steel plates for high-frequency motors, transformers, and magnetic shielding. Generally, motors, transformers, and other electrical components are required to have high efficiency, low power consumption, small size, and light weight. Electrical steel plates are usually guaranteed to have magnetic properties based on core loss and magnetic induction strength. Magnetic induction strength is the number of magnetic lines passing through a unit cross-sectional area of the iron core, also known as magnetic flux density. It represents the material‘s magnetization ability, measured in T. The magnetic induction strength of electrical steel plates is high, and the excitation current (also known as no-load current) of the iron core is reduced. Copper and iron losses are also reduced, which can save electrical energy. When the power of the motor and transformer remains constant, the magnetic induction intensity is high, and the design Bm can be increased. The cross-sectional area of the iron core can be reduced, which reduces the volume and weight of the iron core, and saves the amount of electrical steel plates, wires, insulation materials, and structural materials used. This can reduce the total loss and manufacturing cost of the motor and transformer, and is beneficial for the manufacturing, installation, and transportation of large transformers and motors. The main requirements for the performance of silicon steel are: 1. Low iron loss is the most important indicator of the quality of silicon steel sheets. Various countries classify grades based on iron loss values, with the lower the iron loss, the higher the grade. 2. Under strong magnetic fields, the magnetic induction intensity (magnetic induction) is high, which reduces the volume and weight of the iron core of the motor and transformer, saving silicon steel sheets, copper wires, and insulation materials. 3. The surface is smooth, flat, and the thickness is uniform, which can improve the filling coefficient of the iron core. 4. Good lamination performance is more important for manufacturing micro and small electric motors. 5. The adhesion and weldability of the surface insulation film are good, which can prevent corrosion and improve the punching performan